Which two Interfaces can an administrator use to disable unused Ethernet ports on an ONTAP cluster? (Choose two.)
Which one of the following commands is used to specify the destination appliance(s) that are allowed to replicate (pul data from the source appliance?
Fill in the blank for the following statement using the best answer from the choices that follow. A snapshot is a frozen, read-only image of the entire Data ONTAP file system that reflects the state of the____________at the time the snapshot was created.
Which two configurations ensure end users are able to restore previous versions of files? (Choose two.)
Identify the two SnapMirror commands that are entered on the source storage appliance.
What should be done to non-distuptlvely correct capacity Imbalances in a FlexGroup?
The required hardware to add SyncMirror to an existing system would be ___________.
What is the minimum number of HA pairs required for Epsilon to be automatically assigned?
Which one of the following statements does not apply to the SnapMirror visibility-interval variable?
How can you "throttle" Snap Vault updates and baseline transfers so that the primary or secondary is not transmitting data as fast as it can?
Protection Manager is an optional component of the Operations Manager that can be licensed and accessed from the NetApp Management Console (NMC).
For each Open Systems platform directory to be backed up to the SnapVault secondary storage system, you must execute _____ from the primary to secondary storage system.
Which two choices are used to configure a semi-synchronous SnapMirror relationship? (Choose two.)
When cabling a standard storage appliance for SyncMirror. disk pool 1 volumes must be cabled to Fibre Channel adapter(s) located in what range of slots on the FAS960 appliance?
Which capacity and parity savings feature is configured at the factory with all AFF systems?
If you were troubleshooting and wanted to look at SnapMirror log files, what is the path and directory to these files?
You can avoid data corruption when you issue the cf forcetakeover-d command if the remote node is
Which option of the snap restore command allows you to specify a different directory, as long as the directory already exists?
Which one of the following commands or procedures would you use to undo a SnapRestore reversion?
A NearStore system or storage appliance can operate as a secondary and primary system at the same time.
While troubleshooting a double disk failure with SyncMirror. You decide to remove and destroy a plex from a mirrored volume. What steps would you perform to remove a plex from a mirrored volume?
Which one of the following commands is used to specify the destination appliance(s) that are allowed to replicate (pull) data from the source appliance?
For aggregates or traditional volume SyncMirror to work correctly, the configuration of each plex must be identical with regard to____________.
Refer to the exhibit.
Based on the CPU headroom statistics provided for one node in the cluster, what is the available performance capacity?
Normally, before you split a SyncMirror volume, you ensure that both plexes are
NetApp X1024 Fibre Channel HBA is required on the storage systems for IP over Fibre Channel functionality.
An administrator wants to provide isolation from connected hosts to the same FCP LUN. Which two features accomplish this request? (Choose two.)
In a synchronous SnapMirror configuration, the soui'ce storage appliance exhibits high latency due to user traffic and rapid data change from SnapMirror transactions.Which one of the following tuning methods best resolves this performance behavior? Edit the /etc/snapmirror.conf file on the destination storage appliance and set:
Which ONTAP feature allows the most efficient use of disk space for provisioning root aggregates?
Which option of the snap restore command allows you to specify a different directory, as long as the directory already exists?
Exhibit.
An administrator has a NetApp AFF cluster with Cloud Tiering enabled on all data using the snapshot-only policy. When restoring files, users report slow response times.
What is the highest latency seen during restore?
Which two supported methods would you use to restore data from a SnapVault for Net Backup Volume?
Which one of the following /etc/snapmirror.conf entries will not support synchronous SnapMirror?
What is the maximum number of disk shelves per loop in a fabric-attached MetroCluster?
Which command creates a new SyncMirror aggregate, letting Data ONTAP select the disk drives?
You have quiesced a volume to stabilize the contents of a destination just prior to a snapshot. What is the next logical command that you would issue after the snapshot is complete?
An administrator wants to present datastores to a VMware environment that is using VLAN-10 and creates an SVM with NFS enabled on lif_NFS.
What does the administrator need to correct?
In a fabric-attached MetroCluster, hardware disk ownership by a node is determined by which two factors (Choose two.)
Identify the twoSnapMirrorcommands that are entered on the destination storage appliance.
Which tool is available on a non-NetApp primary system to assist in starting or stopping SnapVault, modifying NDMP settings, enabling debugging, and capturing trace files?
In ONTAP 9.12, what allows an S3 permission to read existing NFS files as objects?
Fill in the blank for the following statement: To manage a SnapVault backup through a commercial NDMP application, you must specify a_____authorized through that application.
TESTED 21 Apr 2025
