LPI 702-100 Dumps Questions Answers

The find command is used to search for files and directories that match certain criteria. The - -type option specifies the type of file to look for, and the d argument means directories. The . argument means the current directory. Therefore, the command find - -type d searches for all directories within the current directory. The other options are either invalid or do not match the question. References: 1: https://www.comptia.org/training/books/a-core-1-220-1101-study-guide, page 301  2: https://www.howtogeek.com/771399/how-to-use-the-find-command-in-linux/, section “The Linux find Command”

The mailer.conf file is used to configure the mailer programs on a BSD system. It allows the system administrator to replace the default mailer programs, such as sendmail, with alternative ones, such as postfix or exim. The mailer.conf file contains a series of entries, each consisting of a label, an equal sign, and a command. The label is the name of the default mailer program, and the command is the path to the alternative mailer program that will be executed instead. For example, to replace sendmail with postfix, the mailer.conf file should contain the following entries:

sendmail /usr/local/sbin/sendmail send-mail /usr/local/sbin/sendmail mailq /usr/local/sbin/sendmail newaliases /usr/local/sbin/sendmail hoststat /usr/local/sbin/sendmail purgestat /usr/local/sbin/sendmail

The mailer.conf file is read by the mailwrapper program, which is a binary that acts as a wrapper for the mailer programs. The mailwrapper program is installed as /usr/sbin/sendmail and /usr/libexec/sendmail/sendmail, and it invokes the appropriate mailer program based on the mailer.conf file. Therefore, to replace the system MTA with another mail server program, the mailer.conf file needs to be updated with the path to the new MTA. References:

• Chapter 31. Electronic Mail | FreeBSD Documentation Portal
• DragonFlyBSD: mta

This line stems from an ARP table because it shows the association between an IP address (192.168.122.1) and a MAC address (52:54:00: a3:4e: 0e) on a network interface (em0). ARP stands for Address Resolution Protocol, which is used to map IP addresses to MAC addresses on a local network. An ARP table is a list of these mappings that is maintained by each host on the network. The other lines are not from an ARP table, but from different sources, such as:

• B. inet 192.168.122.11 netmask 0xffffff00 broadcast 192.168.122.255: This line is from the output of the ifconfig command, which displays the configuration of network interfaces. It shows the IP address, netmask, and broadcast address of the interface.
• C. 127.0.0.1 localhost localhost.my.domain: This line is from the /etc/hosts file, which is used to map hostnames to IP addresses. It shows that the loopback address (127.0.0.1) is associated with the hostname localhost and the fully qualified domain name localhost.my.domain.
• D. tcp4 0 0 192.168.122.11.22 192.168.122.1.38058 ESTABLISHED: This line is from the output of the netstat command, which displays the status of network connections. It shows that there is an established TCP connection between the local host (192.168.122.11) on port 22 and the remote host (192.168.122.1) on port 38058.
• E. localhost link#2 UH lo0: This line is from the output of the route command, which displays the routing table. It shows that the destination localhost is reachable via the link layer interface lo0, which is the loopback interface. The UH flags indicate that the route is up and uses a host-specific gateway. References: 1: https://docs.freebsd.org/en/books/handbook/network-arp/ 2: https://www.freebsd.org/cgi/man.cgi?query=ifconfig&sektion=8 3: https://www.freebsd.org/cgi/man.cgi?query=hosts&sektion=5 4: https://www.freebsd.org/cgi/man.cgi?query=netstat&sektion=1 5: https://www.freebsd.org/cgi/man.cgi?query=route&sektion=8