Black Friday Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: cramtick70

210-015 VCE Vblock System Deployment and Implementation – Virtualization Questions and Answers

Questions 4

You are asked to upgrade the version of the Cisco Nexus 1000V software on the Vblock System 320.

Which component are you upgrading on the hypervisor?

Options:

A.

Service Console

B.

Virtual Supervisor Module (VSM)

C.

Virtual Ethernet Module (VEM)

D.

Virtual Network Interface Card (vNIC)

Buy Now
Questions 5

Which ESXi CLI command is used when installing VIB files on an ESXi host?

Options:

A.

esxcfg vib install

B.

esxcli system vib install

C.

vicfg-module vib install

D.

esxcli software vib install

Buy Now
Questions 6

What is the proper sequence when upgrading the Cisco Nexus 1000V switch module?

Options:

A.

1. Upload new VEM code to bootflash.

2. Install new Cisco Nexus 1000V bin.

3. Verify the upgrade using the show install all status command.

B.

1. Upload new VSM code to bootflash.

2. Install new Cisco Nexus 1000V bin.

3. Verify the upgrade using the show version command.

C.

1. Upload the new VSM code to a USB drive.

2. Install new Cisco Nexus 1000V bin.

3. Verify the upgrade using the show install all status command.

D.

1. Upload the new VEM code to a USB drive.

2. Install a new Cisco Nexus 1000V bin.

3. Verify the upgrade using the show version command.

Buy Now
Questions 7

In which document would you find information regarding issues encountered with software revisions?

Options:

A.

VCE Vblock Administration Guide

B.

VCE Release Certification Matrix

C.

VCE Release Notes

D.

VCE Logical Build Guide

Buy Now
Questions 8

Which two statements are true for vSphere 5.0 vMotion to work correctly? (Choose two.)

Options:

A.

Hosts must be in the same cluster.

B.

Hosts must share the same physical storage.

C.

The virtual machine must be powered on.

D.

The virtual machine must be powered off.

Buy Now
Questions 9

A new VLAN has been configured on your Nexus 1000V for VM data traffic on VLAN 202 using the following commands.

vlan 202

name datavlan-202

port-profile type vethernet VM-DATA-202

vmware port-group

switchport mode access

switchport access vlan 202

no shutdown

max-ports 512

state enabled

After deploying a virtual machine on the new VLAN, connectivity outside of this network does not appear to work.

Which action will resolve the problem?

Options:

A.

Apply the system VLAN attribute.

B.

Use the switchport mode trunk command.

C.

Add VLAN to the uplink port-profile configuration.

D.

Increase default port count.

Buy Now
Questions 10

You are on deployment, and must enable the SSH service on an ESXi host.

In the vSphere client GUI under Configuration, which submenu do you use to complete this task?

Options:

A.

security profile

B.

authentication services

C.

advanced settings

D.

system resource allocation

Buy Now
Questions 11

Your client wants all required storage space for the virtual disk to be allocated at creation time. The data remaining on the physical device should be zeroed out when the virtual disk is created.

Which storage provision type will allow you to meet your client's requirements?

Options:

A.

thick LUN provisioning, eager zeroing

B.

thin LUN provisioning, eager zeroing

C.

thin LUN provisioning, lazy zeroing

D.

thick LUN provisioning, lazy zeroing

Buy Now
Questions 12

Your vSphere environment has two virtual machines configured to use the same VLAN and subnet. The hosts in the cluster are set up to use one DV switch. You want to ensure that the VMs communicate properly on the network and with each other regardless which host they use.

Which action will accomplish this task?

Options:

A.

Consult with your network team to ensure that the ESXi hosts use common routers and switches in your data center environment.

B.

Ensure the ESXi hosts load balancing policy is configured to route based on source mac hash.

C.

Ensure the ESXi hosts load balancing policy is configured to route based on the originating virtual port ID.

D.

The vNic DVPort group must be configured to be the correct setting on both virtual machines for the VLAN they are using.

Buy Now
Questions 13

You enabled access to the ESXi shell. Administrators now complain that they cannot log in to the ESXi shell although you are still logged on.

What would cause this problem?

Options:

A.

The other administrators do not have proper permissions.

B.

The number of connections exceed the limit.

C.

The ESXi shell timeout setting was increased from the default setting of 0.

D.

There is an invalid IP setting on the host.

Buy Now

VCE-CIMIE | 210-015 Questions Answers | 210-015 Test Prep | VCE Vblock System Deployment and Implementation – Virtualization Questions PDF | 210-015 Online Exam | 210-015 Practice Test | 210-015 PDF | 210-015 Test Questions | 210-015 Study Material | 210-015 Exam Preparation | 210-015 Valid Dumps | 210-015 Real Questions | VCE-CIMIE 210-015 Exam Questions

Exam Code: 210-015
Exam Name: VCE Vblock System Deployment and Implementation – Virtualization
Last Update: Nov 25, 2024
Questions: 93
210-015 pdf

210-015 PDF

$25.5  $84.99
 Add to Cart
210-015 Engine

210-015 Testing Engine

$30  $99.99
 Add to Cart
210-015 PDF + Engine

210-015 PDF + Testing Engine

$40.5  $134.99
 Add to Cart